收藏本站
BD8112EFV-M
Technical Note
? Soft Start Function
The soft-start (SS) limits the current and slows the rise-time of the output voltage during the start-up, and hence leads to
prevention of the overshoot of the output voltage and the inrush current.
? Self-diagnostic functions
The operating status of the built-in protection circuitry is propagated to FAIL1 and FAIL2 pins (open-drain outputs). FAIL1
becomes low when UVLO, TSD, OVP, or SCP protection is engaged, whereas FAIL2 becomes low when open or short
LED is detected.
FAIL2
FAIL1
OPEN
UVLO
TSD
OVP
OCP
SHORT
MASK
S
R
Q
SCP
Counter
S
Q
EN=Low
UVLO/TSD
EN=Low
R
UVLO/TSD
? Operation of the Protection Circuitry
? Under-Voltage Lock Out (UVLO)
The UVLO shuts down all the circuits other than REG when VREG ≦ 4.3V (TYP).
? Thermal Shut Down (TSD)
The TSD shuts down all the circuits other than REG when the Tj reaches 175 ℃ (TYP), and releases when the Tj
becomes below 150 ℃ (TYP).
? Over Current Protection (OCP)
The OCP detects the current through the power-FET by monitoring the voltage of the high-side resistor, and activates
when the CS voltage becomes less than VCC-0.6V (TYP).
When the OCP is activated, the external capacitor of the SS pin becomes discharged and the switching operation of
the DCDC turns off.
? Over Voltage Protection (OVP)
The output voltage of the DCDC is detected with the OVP-pin voltage, and the protection activates when the OVP-pin
voltage becomes greater than 2.0V (TYP).
When the OVP is activated, the external capacitor of the SS pin becomes discharged and the switching operation of
the DCDC turns off.
? Short Circuit Protection (SCP)
When the LED-pin voltage becomes less than 0.3V (TYP), the internal counter starts operating and latches off the circuit
approximately after 100ms (when FOSC = 300 kHz). If the LED-pin voltage becomes over 0.3V before 100ms, then the
counter resets. When the LED anode (i.e. DCDC output voltage) is shorted to ground, then the LED current becomes off
and the LED-pin voltage becomes low. Furthermore, the LED current also becomes off when the LED cathode is shorted
to ground. Hence in summary, the SCP works with both cases of the LED anode and the cathode being shorted.
? LED Open Detection
When the LED-pin voltage ? 0.3V (TYP) as well as OVP-pin voltage ? 1.7V (TYP) simultaneously, the device detects as
LED open and latches off that particular channel.
www.rohm.com
? 2010 ROHM Co., Ltd. All rights reserved.
9/22
2011.08 - Rev.C
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
BD8119FM-ME2 IC WHITE LED DVR PWM 28-HSOP
BD82103GWL-E2 IC LED DRVR WHITE BCKLGT 11-UCSP
BD9206EFV-E2 IC LED DRIVER 6V LCD 20HTSSOP
BD9207FPS-E2 IC LED DVR STEPDWN 1.5A TO252S-5
BH-14E_TI-20T_CTI ADAPTER PIN CONVERTER 14-20 PIN
BH-20E_CTI-60T_TI ADAPTER PIN CONVERTER 20-60 PIN
BH-ADP-ISO20 ISOLATION ADAPTER 20-PIN TI JTAG
BH-GANG2000 GANG2000 PROGRAMMER TI 32BIT MCU
相关代理商/技术参数
BD8113EFV 制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type)
BD8113EFV_11 制造商:ROHM 制造商全称:Rohm 功能描述:White Backlight LED Driver for Medium to Large LCD Panels (Switching Regulator Type)
BD8113EFV-E2 功能描述:LED照明驱动器 IC LED DRIVER RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
BD8115F-M 制造商:ROHM 制造商全称:Rohm 功能描述:LED Driver IC
BD8115F-MTE2 功能描述:LED照明驱动器 Auto Grade LED Drvr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
BD8115FP-MTE2 制造商:ROHM 制造商全称:Rohm 功能描述:LED Driver IC
BD8115HFP-MTTR 制造商:ROHM 制造商全称:Rohm 功能描述:LED Driver IC
BD8118FM 制造商:ROHM 制造商全称:Rohm 功能描述:Silicon Monolithic Integrated Circuit